gtag('config', 'G-J1B3LVWC4M');
Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

HX-407™ Mask Making /18,9 kg

HX-407™ Pourable Mask Making Latex is a pre-vulcanized, pourable latex that forms a thick durable skin when poured into a gypsum mold and allowed to “dwell” before spilling out to build layers. Add color with
Fabtone™ pigments

270,39 EUR

precio sin 21% IVA .
unidad


Instructions

SAFETY FIRST:

Keep Out of Reach of Children BE CAREFUL -
Avoid use if you have known allergies to natural latex. Avoid contact with eyes. Flush eyes with water for 15 minutes and seek medical attention. Remove from skin with
waterless hand cleaner followed by soap and water. Children should not use this product without adult supervision.

PROCESSING RECOMMENDATIONS

GENERAL PREPARATION:

Do not allow HX-407 ™ to freeze. The material will not be usable
. Store and use material at room temperature 23°C. This product has a limited shelf life and should be used as soon as possible.
Colder temperatures will slow the working/cure time,while warmer temperatures will reduce working time. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wash thoroughly after handling. Do not eat, drink or smoke in the work area. Keep container closed when not in use.

POURING,CURING & PERFORMANCE:

MIXING AND CURING

Stir before use. Pour into a dry, unsealed gypsum mold. Tilting or lightly vibrating the mold may help to eliminate bubbles if the mold contains complex undercuts or deep details. For a very thin skin, pour the excess latex back into the container immediately or within a couple of minutes. For a thicker skin, allow the product to stay in the mold longer before pouring off excess. As an example,a standing time (or dwell time) of 30 minutes yields a ~1,58 thickness. Two hour dwelling before pouring the excess back into the original conatainer can product a 6,35 mm thickness. Dense plasters are not as absorbent and, therefore, cause thicknesses to
build more slowly. Humidity and ambient temperature will also affect the drying time of latex. Allow HX-407™ to dry in the mold for 12 hours at room temperature prior to pulling it out of the mold.

USING THE CASTING:

Before Demolding, lightly dust the inside of the casting with talc in order to prevent the dry rubber from sticking to itself. Avoid exposing the casting to oils, greases or solvents. Castings should be stored out of direct sunlight.

CLEAN UP:

Clean up wet and dry latex with soap and water.

OPTIONAL - COLORING & STIFFENING THE RUBBER

Fabtone™
latex colorants can be used to dye the latex while in it’s liquid state and HX-Stiffener ™ can be used to make the rubber less flexible.
exposing the casting to oils, greases or solvents. Castings should
be stored out of direct sunlight

Ayuda para elegir

Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • special properties

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Textil

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Cosplay

    Productos para hacer tus propios disfraces y accesorios de cosplay

  • EZ Spray Productos

    es un sistema de pulverización para gomas, plásticos y espumas. Ahorra tiempo y costos laborales en comparación con los métodos de aplicación manual

FormX Newsletter Boletin informativo Información Contacto Tarifas de envío Proyectos Clientes Condiciones de Venta Marcas we have vacancies Aplicaciones Branches FormX Academy

su ventanilla única para materiales de modelado en 3D

Utilizamos cookies para optimizar nuestro sitio web y ofrecerle la mejor experiencia en línea posible. Al hacer clic en "Aceptar todo", usted acepta esto. ¿Más Información?