Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Rubber Glass

Water-Clear Silicone Rubber Perfect for making Flexible Glass & Ice Effects. Rubber Glass® can be used to create a variety of special effects (i.e. simulated broken glass where human contact is required) and model effects (i.e. simulated ice or water). It can also be used for electronic encapsulation applications.Rubber Glass® can be easily broken or “crumbled” into pieces that look exactly like broken glass, ice or diamonds. Vacuum degassing material prior to pouring will produce bubble free castings.

Rubberglass

  • Rubberglass / 0,9 kg.

    Silicona bicomponente de catalizador de estaño. Se utiliza para encapsular objetos y también en Efectos Especiales se utiliza para ficticios de vidrios rotos. Con esta silicona también se pueden conseguir otros efectos como hielo artificial o agua. A+B=1 kg.

    24,50 EUR (precio sin 21% IVA .)

Instructions

MEASURING & MIXING - Materials should be stored and used in a warm environment (73°F/23°C). This product has a limited shelf life and should be use as soon as possible. Mixing containers and stirring sticks should be made of plastic and must be clean and dry. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Dispense One Parts A and One Part B by weight or volume into mixing container. Mix thoroughly for at least three minutes, making absolutely sure that you scrape the sides and bottom of your container several times.

Do not whip or agitate material as this may cause air bubbles. If completely bubble free castings are required, vacuum degassing material prior to pouring will eliminate all bubbles.

Pouring - Pour mixture into a plastic container or mold (ice cube trays or plastic cups made of polyethylene work well). If pouring into or over other surfaces, be aware that cure inhibition is possible (see section below – “Cure Inhibition”). If casting into silicone molds, a release agent (Ease Release® 200 available from Smooth-On) is required.

Curing - Let cure overnight at room temperature (73°F/23°C). Colder temperatures will slow the curing process. Material castings thicker than 2” (5 cm) may take longer to cure. Material is cloudy when first mixed but clears during cure.

Cure Inhibition - If compatibility between the rubber and the surface that you are pouring rubber over is a concern, a small scale test is recommended. Materials found to cause cure inhibition include sulfur-based modeling clays and latex rubber. If pouring Rubber Glass® II over a model surface that you think might cause inhibition, apply a “barrier coat” of clear acrylic lacquer sprayed directly over all surfaces that will come in contact with the Rubber Glass® II is usually effective.

Adhesion: Rubber Glass® II may stick to some surfaces such as glass. A coating of Ease Release® 200 will facilitate release from any surface.

Material Performance - Once material has fully cured it can be removed from the container or mold. Cured Rubber Glass® II is now ready to be displayed as is or broken/crumbled for your specific application.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Ayuda para elegir

Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • special properties

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Textil

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

  • EZ Spray Productos

    is a spraysystem for rubbers, plastics and foams. Saves time & labor costs over hand-application methods

Información Contacto Tarifas de envío Proyectos Clientes Marcas Aplicaciones Branches

su ventanilla única para materiales de modelado en 3D