Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

In & Out® II

IN & OUT® II water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. IN & OUT® II provides a clean, positive release and does not interfere with or affect surface detail and helps minimize air bubbles in finished castings.

Technical bulletin In & Out water soluble release

  • In & Out II water Suluable Release Agent for Concr

    IN & OUT II water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. IN & OUT II provides a clean, positive release and does not interfer...

    14,95 EUR (precio sin 21% IVA .)

  • In&Out Medio despegante para cemento / 3,4 kgs

    IN & OUT ® II medio despegante a base de de agua que ayuda a despegar el hormigón o yeso de los moldes de caucho de Smooth-On.

    68,75 EUR (precio sin 21% IVA .)

  • In&Out Medio despegante para cemento /18,2 ltr

    IN & OUT ® II medio despegante a base de de agua que ayuda a despegar el hormigón o yeso de los moldes de caucho de Smooth-On.

    297,30 EUR (precio sin 21% IVA .)

Instructions

IN & OUT® II IS DILUTED WITH WATER.

Measuring & Mixing - Mix 4 parts water to 1 part In & Out II. Mixing can be done by hand or slow speed mixer. Do not shake or agitate as this may cause product to foam.

How you dilute IN & OUT II® (amount mixed with water, coverage and frequency of application) will depend on the concrete aggregate mix and the form material you are casting into. For example, when casting concrete with a low grit/high sand content (minimal abrasion) into a polyurethane mold, the mix ratio of water to IN & OUT II® can be 4 : 1. High grit content may call for a dilution ratio of 2 parts water to 1 part release agent.

Mix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply.

Application - Apply IN & OUT® II thoroughly with brush, roller or spray. If pressure spraying, pressure should be 25 psi (172 kPa) or higher. For uniform spray applications of release agent, flat spray tips are suggested. Do not allow release agent to puddle.

Caution: Do Not Over Apply. Applying too much release agent will cause air bubbles “wormtracks”, “bugholes” or pitting on surfaces.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

GUIDE

Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • special properties

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Textil

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

  • EZ Spray Productos

    is a spraysystem for rubbers, plastics and foams. Saves time & labor costs over hand-application methods

Información Contacto Tarifas de envío Proyectos Clientes Marcas Aplicaciones Branches

su ventanilla única para materiales de modelado en 3D