Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Epoxi Adhesivos

  • EA40
  • Metalset A4
  • MT13
  • SuperInstant
  • Variobond
  • Sil-Poxy

EA-40® Adhesivo Epoxi Transparente para Laminados

EA-40 Clear Epoxy es un adhesivo epoxi sin relleno que se puede extender fácilmente en películas delgadas, una vez curadas son casi transparentes. La proporción de la mezcla es de 1:1 por volumen. Cuando mezclamos 2A:1B por volumen, el adhesivo EA-40 alcanzará una mayor resistencia al calor y mejorará sus propiedades físicas.

EA-40 es un producto muy versátil y se puede utilizar de muchas maneras diferente. Se utiliza en reparaciónes juntando y pegando joyas, en laminados de madera, para reparar sanitarios, etc. Los fabricantes de arcos utilizan EA-40 como resina de laminación. EA-40 proporciona uniones de alta resistencia a la humedad que cumplen con los requisitos de rendimiento según las Especificaciones Federales MMM-A-188, Tipo III.
EA-40® Adhesivo Epoxi - Tiene un tiempo de curado de 24 horas

boletín técnico

EA-40

  • EA40 Adhesivo de Epoxi / 0,9 kg.

    EA 40 Adhesivo de epoxi transparente. Unidad 0,9 kg.

    34,50 EUR (precio sin 21% IVA .)

  • EA-40 Adhesivo Epoxi Transparente / 7,3kg.

    EA 40 Adhesivo de epoxi transparente. Set 7,3 kg.

    245,90 EUR (precio sin 21% IVA .)

Cómo hacer un arco con epoxi EA-40

Metalset ® A4 adhesivo epoxi- relleno de Aluminio

Metalset A4 ® es un potente adhesivo epoxi que ha sido utilizado durante años por los militares de EE.UU, así como por todas las grandes aerolíneas y fabricantes de automóviles en el mundo. A4 se utiliza en cientos de aplicaciones industriales y ofrece una excelente adhesión a superficies porosas y no porosas. Se puede aplicar en superficies verticales manteniendose en su sitio. Metalset A4 ® cura durante la noche con una contracción insignificante.

Una vez curado, Metalset A4 ® tiene unas buenas cualidades de mecanizado (lijado, taladrado, roscado) y es resistente a los álcalis, ácidos diluidos y disolventes. Entre otras aplicaciones se utiliza para detener fugas en tuberías, válvulas y tanques (por ejemplo en depósitos de gasolina de automóviles), para unir superficies iguales o desiguales, como relleno de juntas metálicas, abolladuras, etc. También se utiliza para fabricar pernos de anclaje en madera y hormigón y para reparar superficies metálicas. El tiempo de curado de Metalset A4 ® es de 16 horas.

boletín técnico

Metalset A4

  • Metalset A4 cola epoxi / 170 gr.

    Cola epoxi pastosa de dos componentes. Unidad 170 gr.

    11,75 EUR (precio sin 21% IVA .)

Instructions

A clean, dry surface is a necessary prerequisite for adhesive bonding. Adhesives will stick to either the surface of which a bond is desired or to that film of extraneous material directly on that surface. Rarely can a structural adhesive penetrate through surface contaminants to provide an optimum bond on an unclean surface.

Porous materials are simple to bond, provided they are dry. The surface should be sanded till clean and free from dust. Non-porous surfaces, such as found on metal and plastic materials, should be degreased, dried and roughened by sanding, sandblasting or chemical etching. The etched or sandblasted surfaces should be covered within a few hours of treatment to prevent contamination.

Handlers should wear clean cotton gloves to prevent body oils from contaminating the clean surfaces.

Epoxy adhesives do not perform well on metals such as nickel, chromium, tin or zinc nor on soft thermoplastics like polyethylene.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING & MIXING - Measure equal amounts of Parts A and B (or 2A:1B) by volume into a clean mixing container. Mixing tools and containers should be clean and made of metal, glass or plastic. After dispensing required amount of Parts A and B into mixing container, mix thoroughly for 3 minutes making sure that you scrape the sides and bottom of the mixing container several times.

Application - Apply to prepared surface and let cure for 24 hours. Applying mild heat will cure EA-40® faster – 150°F/65°C for 6 hours.

Post Curing - After EA-40® has cured at room temperature, heating the epoxy to 150° F (65° C) for 4 to 8 hours will increase physical properties and performance. Let cool to room temp. before moving bonded substrates, machining, etc.

To Attain Maximum Heat Distortion Temperature - let cure for 24 hours at room temperature, heat cure for 2 hours at 250°F (122°C).

At mix ratio 1A:1B – HDT will be 163°F (73°C).

At mix ratio 2A:1B – HDT will be 217° F (103 °C)

Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Store and use material at room temperature (73°F/23°C). This product has a limited shelf life and should be used as soon as possible.

Smooth-On MT13

Smooth-On MT-13 ® es un adhesivo epoxi de rendimiento superior. Se utiliza en aplicaciones que requieren la máxima fuerza de sujeción y la máxima resistencia al agua. MT-13 es un cemento adhesivo epoxi bicomponente que se mezcla en partes iguales por volumen o en peso 100gr.A +123gr.B en unas pocas horas se convierte en un gel. Tiene un curado de 16 horas y se adhiere muy bien a las superficies porosas y no porosas. MT-13 se utiliza en la industria de la navegación para el montaje y para realizar reparaciónes.

boletín técnico

MT-13

  • MT13 Cola epoxi / 142 gr.

    Cola epoxi de dos componentes. Unidad 142 gr.

    13,50 EUR (precio sin 21% IVA .)

Variobond is a two component thixotropic epoxy resin. Recommended as bonding paste for various materials. Solvent free. Excellent adhesion. Easy to apply. Excellent water resistance.

Smooth-On Super Instant Epoxy Adhesive

Smooth-On Super Instant® Epoxi es un adhesivo bicomponente diseñado para proporcionar una unión rápida. Cuando se mezcla en proporciones iguales por volumen o en peso, cura con la suficiente rapidez para permitir el manejo. El tiempo de curado a temperatura ambiente es de 5 a 10 minutos. Super Instant® adhiere de forma inmediata metales como el acero, el aluminio y el bronce, madera, vidrio, mampostería y muchos plásticos duros.
Super Instant® Epoxy - 5-10 minutos de curado

boletín técnico

FEATURES

DESCRIPTION
Variobond is a thixotropic, two component bondin
g paste based on solvent free epoxy resins and
polyamine adduct hardeners.

PRINCIPAL CHARACTERISTICS
• Suitable as adhesive for bonding various materials such as wood, steel, aluminium, plastics and
their combinations;
• Also suitable as multi-purpose filler for steel, wood, GRP, etc.;
• Recommend for fillet-joints;
• Good adhesive power;
• Excellent water resistance;
• Easy mixing as both components are thixtropic;
• Easy application;
• Suitable for woodcore epoxy constructions;
• Also available in mahogany colour, packed in a cartridge.

COLOURS AND GLOSS
Opaque or Mahogany - Gloss

BASIS PROPERTIES (AT 23 ̊C AND 50% R.H.)
Density : approx. 1,4 g/cm3 (mixed product)
Solid content : approx. 100 % (volume)
Recommended d.f.t. : depending on application
Dust dry after : approx. 24 hours
Full cure after : approx. 2 days, see additional information
Recoating interval : min. 24 hours, see additional information
max. unlimited
Shelf life : separate components, stored cool and dry in original packaging, minimum
12 months Flash point (DIN53213) : base component 150 ºC
hardener 112ºC
SPREADING RATE
Depending on application: approx. 1,0 - 3,0 m2/kg, see additional information
The practical spreading rate depends on a number of variables, such as: shape and size of object to be painted, the condition and profile of the substrate, the method of application, climatologic conditions and skill of labour.

SUBSTRATE CONDITION AND TEMPERATURE
Wood : clean and dry, free from any contamination and loose particles, moisture content maximum 12%, pre-treated with Variopox Injection resin and/or Variopox Impregnating resin and sanded with grit paper P120;
Metals : clean and dry, free from oil, grease, contamination and loose particles, pre-treated with IJmopox ZF primer and sanded with grit paper P120;
Concrete: clean and dry, free from any contamination and loose particles, moisture content maximum 4%, pre-treated with Variopox Injection resin;
Polyester : clean and dry, free from contamination and loose particles, exposed glass fibres pre-treated with Variopox Injection resin and sanded with grit paper
P120; Other surfaces : clean and dry, in good condition, free from any contamination and loose
particles, sanded with grit paper P120;

Super Instant Epoxi

  • instant epoxy / a+b 142gram

    Cola epoxi súper instantánea de dos componentes. A+B 142 gr.

    16,00 EUR (precio sin 21% IVA .)

Variobond Adhesivo Epoxi

  • Vario Bond 280 ml tubo

    Vario Bond 280 ml tubo

    25,10 EUR (precio sin 21% IVA .)

  • Vario Bond 1000gr

    Adhesivo epoxi sin disolventes (no gotea). Se utiliza para unir de forma permanente materiales diversos. Color: ópalo. 1 kg.

    30,95 EUR (precio sin 21% IVA .)

Instructions

Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Store and use material at room temperature (73°F/23°C). This product has a limited shelf life and should be used as soon as possible.

A clean, dry surface is a necessary prerequisite for adhesive bonding. Adhesives will stick to either the surface of which a bond is desired or to that film of extraneous material directly on that surface. Rarely can a structural adhesive penetrate through surface contaminants to provide an optimum bond on an unclean surface.

Porous materials are simple to bond, provided they are dry. The surface should be sanded till clean and free from dust. Nonporous surfaces, such as found on metal and plastic materials, should be degreased, dried and roughened by sanding, sandblasting or chemical etching. The etched or sandblasted surfaces should be covered within a few hours of treatment to prevent contamination.

Epoxy adhesives do not perform well on metals such as nickel, chromium, tin or zinc nor on soft thermoplastics like polyethylene. Refer to the Preparation of Surfaces for Adhesive Bonding technical bulletin.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MIXING AND APPLYING...

Measure equal amounts of Parts A and B (or 100A:123B by weight) and mix thoroughly for 3 minutes to a uniform color (no streaks). Apply to prepared surface at a thickness of 1/32” - 1/16” (0.08cm - 0.16cm). Fit other surface over epoxy and apply even pressure using clamps or weights until material cures.

CURING...
MT-13® will cure and reach handling strength in 16 hours at room temp. (73°F/23°C). Applying uniform mild heat will cure epoxy faster–150°F/65°C for 4 hours. Let cool to room temperature before moving bonded substrates.

Instructions

A clean, dry surface is essential for successful adhesive bonding. Porous materials are simple to bond, provided they are dry. The surface should be sanded till clean followed by wiping surface with solvent (acetone, MEK, mineral spirits). Let solvent evaporate fully before applying A4.

Non-porous surfaces (metals, plastics, coated woods) should be sanded, sandblasted or chemically etched. If sanding or sandblasting, follow with solvent wash. Let solvent evaporate fully before applying A4. Epoxy adhesives do not perform well on metals such as nickel, chromium, tin or zinc or on soft thermoplastics like polyethylene. An option would be to try a polyurethane adhesive (such as URE-BOND® from Smooth-On).

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING, MIXING, APPLYING...
Metalset™ A4 is mixed one part A to one part B by weight or volume. If dispensing from tubes, squeeze out equal amounts from each tube. Try to be as accurate as possible. Mix thoroughly for 3 minutes to a uniform grey color (no streaks) and apply to prepared surface at a thickness of 1/32” - 1/16” (0.08cm - 0.16cm). Fit other surface over epoxy and apply even pressure using clamps or weights. Handling time is 4 hours. Full cure is 16 hours.

CURING...
Metalset™ A4 will cure in 16 hours at room temp. (73°F/23°C). Applying mild heat will cure A4 faster–150°F/65°C for 2 hours.
Post Curing - After A4 has cured at room temperature, heating the epoxy to 150°F (65°C) for 4 to 8 hours will increase physical properties and performance. Let cool to room temperature before moving bonded substrates, machining, etc.

Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Store and use material at room temperature (73°F/23°C). This product has a limited shelf life and should be used as soon as possible.

CERTIFYING TO BELL SPEC...
Metalset™ A4 meets all quality requirements and can be certified to Bell Spec 299-947-099 Rev. D, IOM 80-2017-017. There is a fee associated with certification. Contact Smooth-On, Inc. for further information at (610) 252- 5800 (8:30-5:30 Eastern Time).

Instructions

Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Store and use material at room temperature (73°F/23°C). This product has a limited shelf life and should be used as soon as possible.

A clean, dry surface is a necessary prerequisite for adhesive bonding. Adhesives will stick to either the surface of which a bond is desired or to that film of extraneous material directly on that surface. Rarely can a structural adhesive penetrate through surface contaminants to provide an optimum bond on an unclean surface.

Porous materials are simple to bond, provided they are dry. The surface should be sanded till clean and free from dust. Non-porous surfaces, such as found on metal and plastic materials, should be degreased, dried and roughened by sanding, sandblasting or chemical etching. The etched or sandblasted surfaces should be covered within a few hours of treatment to prevent contamination. Handlers should wear clean cotton gloves to prevent body oils from contaminating the clean surfaces.

Epoxy adhesives do not perform well on metals such as nickel, chromium, tin or zinc nor on soft thermoplastics like polyethylene. Refer to the Preparation of Surfaces for Adhesive Bonding technical bulletin.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Measuring & Mixing - Squeeze out equal amounts onto a disposable surface and mix thoroughly. Mixing tools and containers should be clean and made of metal, glass or plastic. After dispensing required amount of Parts A and B into mixing container, mix thoroughly making sure that you scrape the sides and bottom of the mixing container several times.

Sil-Poxy™ is a one component adhesive made specifically forbonding Smooth-On RTV moldmaking silicone rubbers to silicone rubber and other substrates including some plastics (urethane), plasters/ceramics, fabrics, etc.

Sil-Poxy™ will work with tin- or platinum-cure silicones and provides a strong, flexible bond between silicone parts with high elongation. Can be colored with Silc-Pig™ silicone pigments. Cured adhesive resists weathering, moisture, UV and high temperatures.

Sil-Poxy™ can be used repairing torn silicone rubber molds. Other applications include bonding silicone for prosthetics and animatronics
Features

Can be used repairing torn silicone rubber molds.
Will work with tin- or platinum-cure silicones
Provides a strong, flexible bond

Guia

Permítanos ayudarle a encontrar lo que busca.

La lista a continuación puede ayudarle a encontrar lo que está buscando a través de una ruta alternativa.

Ayuda para elegir

Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.

  • Lifecasting

    aqui puede encontrar una amplia gama de productos para aplicar directamente sobre la piel. Alginatos, siliconas cosméticas y vendas de yeso.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • Productos Transparentes

    Resinas de PU, gomas de PU, epoxi y siliconas cristalinas para usos industriales y también para la industria del cine.

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Modelar con Epoxi

    Masillas epoxi bicomponentes que le permiten modelar

  • Resinas de Producción

    Una amplia gama de resinas bicomponentes para hacer coladas o para aplicar a brocha (tixotrópicas); Poliuretano, Epoxi, Poliester y acrílicas.

  • Resinas Semi Rígidas

  • Accesorios

    Todo lo que necesita para realizar su trabajo; Guantes, Cubiletes graduados, Espátulas, Brochas, etc.

  • Carcasas & Soportes

    Todos los materiales que se utilizan para fabricar carcasas y soportes, como masillas de epoxi y de polyuretano, vendas de escayola etc.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Textil

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

Marcas Aplicaciones Contacto Tarifas de envío Información Nuevo en..

su ventanilla única para materiales de modelado en 3D