additivesMedios para desmoldar y aplicar sobre todo tipo de superficies.
Boletín Técnico One Step
Boletín Técnico Ease Release 200 & 205
Boletín Técnico Ease Release 300
Boletín Técnico Ease Release 400
Boletín Técnico Ease Release 2831
Boletín Técnico In & Out water soluble release
Boletín Técnico Universal Mold Release
Boletín Técnico Super Seal
Boletín Técnico Sonite Wax
Tenemos una amplia gama de productos para desmoldar y para aplicar sobre todo tipo de superficies. Estos productos los presentamos en aerosoles o en líquidos. También tenemos disolventes a base de agua que han sido especialmente formulados para aplicar a los moldes en coladas de yeso y cemento.
One Step® Release Agent And Sealer sella las juntas y prepara las superficies porosas en una sola aplicación (dos en uno)
Ease Release® Release Agent cubre casi todas las necesidades en trabajos con moldes y réplicas
In & Out® II Desmoldante a base de agua para el hormigón. Es un concentrado económico para desmoldar coladas de hormigón, se utiliza con todos los moldes de caucho de Smooth-On. No afecta a los detalles de la superficie de las piezas y prolonga la vida del molde.
Universal Mold Release® Se utiliza para aplicar sobre la pieza original. Separa con facilidad las gomas de poliuretano. Sin embargo no es un producto adecuado para utilizarlo con siliconas.
One Step® is a convenient, economical liquid sealing agent and release agent in one. This non-flammable, non-VOC formula is offered as a "one step" alternative to using a sealing agent followed by a release agent during the mold making process using Smooth-On urethane mold rubbers.
One Step® will facilitate the release of cured urethane mold rubber from plaster, concrete, stone, brick, marble, limestone, wood, metal and other surfaces. Do not use on modeling clays.
Technical bulletin One Step
Ease Release® 200 and 205 is an excellent general purpose release agent for making molds and casting parts. This product will release urethane rubber, urethane resins, polyester resins, RTV silicones, and thermoplastic polymers. Ease Release® 200 and 205 is effective on urethane, silicone and metal molds.
Ideal For Releasing:
~ Urethane Rubber From Original Models
~ Urethane Plastic From Urethane Rubber
~ Silicone Rubber From Original Models
~ Silicone Rubber From Silicone Rubber
~ Urethane Plastic From Silicone Rubber
Technical bulletin Ease Release 200 & 205
Technical bulletin Ease Release 300
Technical bulletin Ease Release 400
NOT FOR USE WITH URETHANE FOAMS For releasing foam, use Ease Release 2831
Ease Release® 2831 is a wax-based non-silicone liquid release agent. It has proven to be effective when used to release polyurethane foams. This wax dispersion is designed to operate at mold temperatures ranging from 160°F to 200°F with minimal wax build-up. EASE RELEASE 2831 works with aluminum, steel, and elastomeric mold construction. Looking for a different Mann product? View the Mann mold release agent product line.
Technical bulletin Ease Release 2831
IN & OUT® II water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. IN & OUT® II provides a clean, positive release and does not interfere with or affect surface detail and helps minimize air bubbles in finished castings. Simplify Your Production Casting With IN & OUT II®
- Will Not Stain / Soften Concrete Or Gypsum Surfaces
- Mix With Water - Economical
- Will Not Affect Color Pigmenting Of Cast Concrete
- Minimizes “Bug Holes” In Concrete And Air Bubbles In Gypsum Castings
- Keeps Molds Clean - Does Not Build Up
- Significantly Extends Mold Life
IN & OUT® II IS DILUTED WITH WATER. Mix 4 parts water to 1 part In & Out® II. Mixing can be done by hand or slow speed mixer. Do not shake or agitate as this may cause product to foam. How you dilute IN & OUT® II (amount mixed with water, coverage and frequency of application) will depend on the concrete aggregate mix and the form material you are casting into. For example, when casting concrete with a low grit/high sand content (minimal abrasion) into a polyurethane mold, the mix ratio of water to IN & OUT II® can be 4 : 1. High grit content may call for a dilution ratio of 2 parts water to 1 part release agent. Mix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply.
Technical bulletin In & Out water soluble release
Universal Mold Release® is formulated especially for mold making and casting, and works well with most liquid rubber and liquid plastic products. It will release mold rubbers (such as polyurethanes and polysulfides) from properly prepared models. Sealing porous models (wood, plaster, concrete) or certain modeling clays (containing water or sulfur) with Smooth-On SuperSeal® or other sealer may be necessary. If using silicone rubber, seal model surface with SuperSeal® only. Do not use UMR.UMR also easily releases a variety of casting materials (epoxies, Smooth-On liquid plastics, etc.) from cured rubber molds. Properly used, Universal Mold Release improves molding efficiency for a variety of casting applications and will actually lengthen the life of your production mold.
- Available in aerosol or bulk liquid.
Technical bulletin Universal Mold Release
One Step® Release Agent And Sealer seals and releases porous originals in one step.
SuperSeal® was developed as an economical, fast-drying sealing agent for a variety of surfaces including modeling clays, gypsum plasters, concrete and wood.
Sonite® Wax is a soft paste wax used to seal porous surfaces and will aid in releasing urethane mold rubber from a variety of model surfaces, plastics from plastics and other industrial applications.
U-10 Soap Solution, to seal plaster models before applying mold rubber.
And the Kwikee® Sprayer, an economical alternative to aerosols for dispensing release agents and sealing agents.
SuperSealTM was developed as an economical, fast-drying sealing agent for a variety of surfaces including modeling clays, gypsum plasters, concrete and wood.
This sealing agent will quickly and effectively seal surfaces without interfering with surface detail. The new formula offers better performance and faster evaporation. Mold rubber can then be applied.
This product incurs a ground hazard shipping fee when shipped in the gallon size.
Technical bulletin Super Seal
Sonite® Wax is a soft paste wax used to seal porous surfaces and will aid in releasing urethane mold rubber from a variety of model surfaces, plastics from plastics and other industrial applications. (It may be necessary to follow application of Sonite® Wax with suitable mold release agent such as Universal Mold Release®). Consult technical bulletin of mold rubber product for complete details.
Technical bulletin Sonite Wax
The Kwikee® Sprayer is an economical alternative to aerosols for dispensing release agents and sealing agents. It is a faster, labor-saving way to cover large models or molds and delivers sealing agent or release agent in a fine mist.
Let us help you find your way.
The list below may help you find what you are looking for via an alternative path.
Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.