Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Glow Worm

Glow Worm polvo, resplandor en la oscuridad

Los polvos fosforescentes Glow Worm® pueden añadirse a los plásticos, gomas y espumas de Smooth-On para crear objetos que brillan en la oscuridad después de ser expuestos a la luz. Elija entre el verde y el azul.

La diferencia entre los polvos Glow Worm® y otros polvos similares, es que las piezas hechas con los polvos Glow Worm® brillarán en la oscuridad 10 veces más que otros polvos fluorescentes.

Los objetos que brillan en la oscuridad se utilizan en: Halloween, proyectos de hobby, en el hogar, acuarios, escaparates de tiendas y mucho más. Estos materiales también se utilizan para fabricar señales de seguridad para la industria, municipios y más.

Boletín Técnico

Ficha de Seguridad
MSDS

Glow Worm Pigmentos

  • Glow Worm Azul / 170 gr.

    Glow Worm® Azul - Polvo Fosforescente que Brilla en la oscuridad con un tono Azul. Recomendamos mezclar por volumen: 1A + 1B + 1 Glow Worm.

    31,75 EUR (precio sin 21% IVA .)

  • Glow Worm Verde / 170 gr

    Glow Worm® Verde - Polvo Fosforescente que Brilla en la oscuridad con un tono Verde. Recomendamos mezclar por volumen: 1A + 1B + 1 Glow Worm.

    50,20 EUR (precio sin 21% IVA .)

  • Glow Worm Azul / 1 kg

    Glow Worm® Azul - Polvo Fosforescente que Brilla en la oscuridad con un tono Azul. Recomendamos mezclar por volumen: 1A + 1B + 1 Glow Worm. Bote 1kg

    189,55 EUR (precio sin 21% IVA .)

  • Glow Worm Green / 1 kg

    Glow Worm® Verde - Polvo Fosforescente que Brilla en la oscuridad con un tono Verde. Recomendamos mezclar por volumen: 1A + 1B + 1 Glow Worm. Bote 1kg

    204,55 EUR (precio sin 21% IVA .)

Instructions
For best results, use Glow Worm® powders with a fast-curing translucent resin such as Smooth-Cast® 325. The fast curing resin allows uniform filler dispersion throughout the finished casting. If the resin system is too slow, fillers may settle unevenly in the finished casting. Glow Worm® powders can also be added to translucent / clear silicone rubbers such as Dragon Skin® or EcoFlex® Series for glow in the dark props that are soft and flexible. Glow Worm® powders can also be blended to create additional finished effects.

Directions for Use – Pre-mix all liquid resin, rubber or foam before dispensing. Store and use all materials at or near 73°F/23°C. Glow Worm® powders must be kept dry (see ’Guarding Against Moisture’ section). Use with adequate ventilation. Read and follow directions for material used to mix with Glow Worm® powders. The following example features SmoothCast® 325 (A+B) mixed with Glow Worm® powder. The powder must be thoroughly dispersed into a two component liquid resin or rubber to a uniform consistency.

Recommended Mix Ratio by Volume: 1A + 1B + 1 Part Glow Worm® powder.

By Volume Mixing & Casting Procedure:

Dispense 1 cup of Smooth-Cast® 325 Part B into a clean mixing container.
Dispense 1 cup Glow Worm® powder into mixing container.
Mix thoroughly.
Dispense 1 cup of Smooth-Cast® 325 Part A into mixing container.
Mix for 30 seconds until all filler particles are dispersed and pour into rubber mold.
Lower Your Cost Per Casting - Glow Worm Powders are Expensive: Mix small amounts as directed above and brush layers into a mold to coat the mold cavity (known as a face coat or gel coat).

Optional: Combine Smooth-Cast®/Glow Worm® mixture with 1 part Ure-Fil® 11 to increase brushability of gel coat. Follow by backfilling with straight resin or foam.

The glow effect will be the same vs. a solid casting and material cost will be greatly reduced.

Guarding Against Moisture – All powders will absorb atmospheric moisture over time which will react with urethane resins. If you notice a moisture reaction between resin and powder or suspect that your Glow Worm® powder contains moisture, you can remedy by spreading powder evenly over a metal cookie sheet at ¼” (0.6 cm) thickness and bake in oven for 4 hours at 150° F/60° C. Allow to cool before mixing powder with resin. Store powder in a tightly closed container in a cool, dry environment with a desiccant pouch (available at your local hobby/arts and crafts store). Replace used desiccant pouches every other time you open container.

Glow Worm® Powders are up to 50% brighter than the competition.

GUIDE

Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

Información Contacto Tarifas de envío Proyectos Clientes Marcas Aplicaciones Branches

su ventanilla única para materiales de modelado en 3D